45KW Low-Frequency Dual-Station Induction Heater 1-20KHz

$13,990.00

Across International’s IHL series 1 kHz to 20 kHz low frequency induction heaters are good for a wide range of applications including deep heat penetration for full hardening processes, steel rod forging, tempering of pressing dies, pre-heating for welding, and melting of metal batches over 4 lbs. They are not limited to ferromagnetic materials, so nonferrous metals can also be used effectively.

Product total
Options total
Grand total
SKU: IHL45AB Category:

Description

Note: This model only available in 460-480 volt three-phase.

Across International’s IHL series 1 kHz to 20 kHz low frequency induction heaters are good for a wide range of applications including deep heat penetration for full hardening processes, steel rod forging, tempering of pressing dies, pre-heating for welding, and melting of metal batches over 4 lbs. They are not limited to ferromagnetic materials, so nonferrous metals can also be used effectively.

There are three major components to the system: the power supply, the compensating capacitor/transformer and the induction coil/smelting crucible. Our heaters automatically adjust to the best resonant frequency in order to achieve the most efficient overall heating results based on our customer’s requirements which include heat penetration, heating efficiency, operating noise and electromagnetic homogeneity. Two of our most popular low frequency machines are the Melting Furnaces with Tilt-Pour Melter and Auto-feeding Rod Heating Furnaces for Forging.

Main Features

  • Dual-station with connection cables and hose let you separate the heater and controller up to seven feet, allow you to stay away from high temperature, dirty and corrosive environment and for a safer operation, or if you need to move the heater to your work pieces constantly during operation.
  • Ease of use: just plug in the power and connect the water cooling system. Our simple instruction allows you to use the heater in 15 minutes.
  • Light weight, portable (with built-in handle), instant heat and up to 90% energy savings.
  • Precise control with digital time and current displays.
  • Remote foot switch for safer operation.
  • Dual automatic and manual modes.
  • Optional graphite and silica crucibles available. (melting material decides crucible type, weight and size of the material decide crucible size)
  • Custom coil design (fixed coil or coil on a cable so it can be used by hand like a wand).
  • ISO 9001:2008 registered manufacturer.
  • We provide sample testing and custom made coils in our New Jersey facility.

Safety Features

  • Overvoltage protection: machine shuts down when input voltage is over 495V. Overvoltage light will turn on and buzzer will sound continuously. Alarm and light shut off automatically when voltage goes below 495V.
  • Overheat protection: if sensor detects heat radiatortemperature is over 55C, machine will shut down, overheat light will turn on and buzzer will sound continuously. Increase water pressure or lower water temperature until alarm goes off itself.
  • Overcurrent/malfunction protections: machine will shut down, indicator light turned on and buzzer sounds continuously if one of these situations occurs:
  • One of the machine parts becomes overheated
    Interfering signal detected
  • Short circuit between work pieces and induction coils
  • Machine malfunctions
  • Induction coils touching each other
  • Input voltage is too low
  • Low water pressure protection: if water pressure goes below 29 PSI, machine will shut down, water protection light will turn on and buzzer will sound continuously.

CAUTION

  • Always wear protective gear and goggles when operating the machine. Crucibles must be covered all the time during operation. Across
  • International is not responsible for any injury or damage caused by misuse.
  • Do not run no-load operation for a long period of time, it might cause damage to the machine.Circulating water must be pure, clean and below 45C.
  • Machine must be grounded properly all the time during operation.
  • Do NOT use single-turn coil if coil diameter is smaller than 4 inches, it will cause high frequency damage to the machine.
  • Thread tape (or related material) is absolutely prohibited during installation of induction coils.

 

 

Specifications

 Max. input current55 A (min. 70A circuit breaker required)
Power480 VAC 50/60Hz 3-phase (380V available upon request)
Power Cord 4-gauge 4-conductor Max 60A (4/4 SOOW for 3 PH system)
 Output frequency 1-20 KHz
 Output current 10-70 A
 Output voltage 70-550 V
 Max. oscillating/input power 45 KW
 Duty cycle 100% (24 hours continuous use)
 Air cooling Rear fan
 Water pressure ≥ 0.2 Mpa (29 PSI) you may use tap water
and water pump (>1/4HP & >240 Gph)
 Water flow > 1 gallon (4 liters) per minute
 Induction coil Copper tubing, custom coils available
 Unit dimensions (WxDxH)Power supply: 10.5 x 22 x 18.5″
Transformer: 19 x 23 x 29″
Shipping dimensions (WxDxH)/Weight 32 x 26 x 29″ / 188 lbs
 Connection cables7 feet

Standard package

Part descriptionQuantity
Part image
 IHL45 induction heater1 set
Connection cable1 set
 Foot switch (7 ft)1 pc
 Optional copper tubing induction coil made according to customer’s requirementsOn Demand
 Stainless steel hose clamp1 set
Fuse1 set
User’s manual1 pc

Reviews

There are no reviews yet.

Be the first to review “45KW Low-Frequency Dual-Station Induction Heater 1-20KHz”

Your email address will not be published. Required fields are marked *